SwitchPilot 3 m/ Display, 4 utganger + 2 x Servo

kr 569,00
Tilgjengelighet: På lager
Kun 3 igjen

30 dager bytterett


Frakt fra 89 kr, Gratis frakt over 3000 kr


Lynrask levering


750 m² butikk i Oslo


ESU SwitchPilot versjon 3 multiprotokoll (DCC/Motorola) m/ display for enkel programmering.

Tilbehørsdekoder/funksjonsdekoder for signaler, lamper, pensemotorer, servoer og annet tilbehør. 4 utganger for pensemotor (spolemotor) eller 8 funksjoner (lys, avkoblere etc). 2 servoutganger.

Mer informasjon på Engelsk:

SwitchPilot 3 decoders are optimized for stationary use on your system and can switch conventional double coil switch drives, light signals, magnetic uncouplers, light bulbs or other stationary consumption.In order to facilitate the rather cumbersome configuration of magnetic article decoders, the SwitchPilot 3 has an innovative operating concept consisting of a 4-line, illuminated OLED display and three input buttons.


The SwitchPilot 3 is multi-protocol and can be used with workstations according to the Märklin Motorola system (e.g. 6021, Central Station or Mobile Station) as well as DCC-enabled control panels. The configuration can take place on both the main track and the programming track. Thanks to RailCom, CVs can also be read out.


The SwitchPilot 3 can be supplied directly from the digital system or from an external DC or change voltage source. It has a total of 8 transistor outputs, which are grouped in the 4 exit pairs 1 to 4. Each output pair contains two outputs (OutA and OutB) and can be configured individually for the desired use case:In pulse mode, the output is switched on as soon as a switching command is received. The fact that the output automatically switches off again as soon as the time stored in the decoder has elapsed prevents the burning of magnetic article drives.At the moment (K83-compatible) the output remains active as long as the button on the control panel is pressed. This operating mode is suitable for turnout drives with final shutdown or for de-caps.In bi-stable continuous operation (k84-compatible), the two outputs are switched on and off: When pressing the first button (red) on the control panel, the output Out A is switched on. It remains active until pressing the assigned button (green) activates the output Out B of the same output group. Out A and Out B behave like a change switch.In alternating flasher mode, the outputs Out A and Out B of an output pair are switched on alternately with an adjustable flashing frequency. The change indicator is started with the command "Ge- rade/Green" of the assigned button and stopped again with the command "Branching/Red".Optionally, the output can also be slowly dimmed and dimmed (so-called "zoom" for glow lam pen simulation).With the switch 3 mode switch, you can switch all output pairs together to the "k83" or "k84" modes at lightning speed, regardless of how they are configured.


Since the SwitchPilot 3 is RailCom-capable, all settings can be read out and changed directly in the built-in state on request. In combination with an ECoS as an ideal "partner", the SwitchPilot 3 can record and display the actual turnout setting with appropriately prepared turnout drives. Finally, you have the certainty that your switch has switched correctly!


The SwitchPilot 3 can be flexibly adjusted either on the programming track with DCC control panels or on the main track with POM ("Programming on Main") or can also be read out via RailCom CVs. On request, he also learns the addresses directly via a programming button. The easiest way to set is, of course, with the integrated OLED display and the three input buttons: All settings can be checked directly on the decoder and changed on request. A"Programming" with the help of your control panel is not required. It really can't be any easier. The ESU LokProgrammer can be used for firmware updates.

Mer informasjon

Mer informasjon
Artikkelnr. ESU51830
Produsent ESU