Sikre dine julegaver - vi pakker og sender daglig helt frem til jul!
x
c

Åpent kjøp i 30 dager

d

Gratis frakt over 3000 kr

e

Sendes innen 24 timer

Passion for trains
Passion for trains
0 item(s)

Du har ingen varer i handlekurven.

  • Forhåndsbestill
    ESU58410 - Loksound V5 m/ Høyttaler, NEM 652 plugg a
Forrige

ESU MTC 21 Extention

Forrige

Lokpilot V4 M4, Quad Protokoll, MTC 21

Loksound V5 m/ Høyttaler, NEM 652 plugg

Artikkelnummer:
1012545
Produsentens varenr.:
ESU58410
Produsent:
ESU
kr 999,00

Tilgjengelighet: Forhåndsbestill  j

Alltid tilgjengelig

Nå kan du bestille kommende nyheter eller varer som ikke er på lager. Varen vil bli sendt til deg så fort vi får den inn på lager. Vær oppmerksom på at forhåndsbestillinger er avhengig av tilgjengelighet fra våre leverandører. Lange leveringstider kan forekomme. Alle forhåndsbestillinger er uforpliktende og kan kanselleres ved å sende oss en epost.

-
+
c

Åpent kjøp i 30 dager

d

Gratis frakt over 3000 kr

e

Sendes innen 24 timer

f

750 m² butikk i Oslo

Beskrivelse

ESU Loksound V5 med NEM 652 (8-pins) plugg og 11 x 15 mm elektrostathøyttaler.

NB NB: Denne lyddekoderen leveres i utgangspunktet uten lyd, men ved bestilling kan man spesifisere ønsket lyd fra ESU, så programmerer vi denne med rett oppsett og lyd.


Mer informasjon på Engelsk:

The LokSound 5 is the most important member of the LokSound family. Due to the combination of the digital decoder and the sound module on one circuit board we achieve the smallest possible dimensions of 30 mm x 15.5 mm. Therefore it fits into almost any H0 or 0 gauge locomotive.

LokSound 5 decoders are available with all popular interface types and are supplied with a sugar cube speaker (11 mm x 15 mm) and a sound enclosure.

Operating modes

Like all products of the LokSound family the LokSound 5 is a true multi protocol decoder. It supports DCC as well as Motorola®, Selectrix® and M4. Of course it supports 14 through to 128 speed steps as well as 2 and 4 digit addresses in DCC format and up to 32 functions. Thanks to RailComPlus® the decoders register themselves fully automatically on suitable command stations.

This decoder supports all DCC programming modes and thanks to RailCom® you may read out the CV values on the main, provided you have a command station supporting RailCom®. There are utility registers for command stations that only facilitate programming of CVs ranging from 1 to 255.

Motorola® users benefit from up to 28 speed steps for 255 addresses. Three additional Motorola® addresses facilitate triggering of 16 functions. An integral programming mode even allows programming with the good old Central Unit 6021.

The M4 protocol supports the automatic registration on mfx® compatible central units.

The LokSound 5 decoder supports the Märklin® braking sections just as well as the ZIMO® HLU braking commands or the Lenz® ABC system. Braking with DCC brake generators or with DC is also possible. Furthermore the locomotive with a LokSound will come to a halt when a Selectrix® braking diode is switched into the circuit. The ABC push-pull feature enables the automatic commuting between two stations.

The LokSound 5 decoder is also suitable for analogue DC and AC (!) layouts.

Sound

The LokSound 5 decoder can reproduce up to 10 channels simultaneously. Each channel offers up to 16 Bit / 31250 kHz and thus we have finally achieved hi-fi sound quality on your layout. For all practical purposes one cannot detect any difference to the original. A class D audio power amplifier with up to 3W output power feeds the speakers with a permitted impedance of 4 – 32 Ohms. The huge 128 MBit sound memory assures sufficient storage capacity.

The volume of all individual sound fragments may be adjusted separately. The outstandingly flexible sound engine without a rigid flow chart facilitates a prototypical simulation of all conceivable rail vehicles. Three separately adjustable braking functions and two alternative load scenarios provide you with maximum control of your vehicles

Functions

We are quite aware that you want your locomotives to be as realistic as possible. Therefore we have packed many function outputs into it. Subject to the type of interface every LokSound 5 has at least 10 amplified outputs. The decoders with PluX22 or 21MTC interface have an additional 4 outputs for controlling servos or as logic outputs. Of course, all important lighting functions are supported. The brightness of each output may be adjusted separately. The decoder supports the automatic push and pull movements – known as the coupler waltz – required for reliable operation of digital couplers such as the ones by ROCO® and Krois® as well as Telex® couplers.

Motor control

Motor control of the LokSound 5 has been further improved. A variable PWM pulse frequency ranging from 10 kHz to 50 kHz assures perfect silent operation, particularly for coreless motors. Thus the typical hum is a thing of the past. Load control can now be adjusted with up to 10 separate CVs and thus will manage even the most difficult cases. The unique “Auto Tune” function facilitates the automatic calibration of the decoder to perfectly match the motor. The LokSound 5 decoder supplies up to 1.5A motor current, which is quite sufficient even for older motor types.

Dont worry when you forget the syntax of an HTML element, like and iframe, a link, a table, an image or anything else. Go to HTML CheatSheet and generate the code you need.

Spesifikasjon

Produsent ESU

Product was successfully added to your shopping cart.